Engineers 3-D-print a miniaturized spectrometer

3D-printed miniature spectrometer. a, wave-optical simulation of the spectrometer. b, microscope image of the fabricated spectrometer overlayed with the intensity distribution from a. c, array of fabricated spectrometers. Credit: Andrea Toulouse, Johannes Drozella, Simon Thiele, Harald Giessen, and Alois Herkommer

The miniaturization of spectroscopic measurement devices opens novel information channels in medical science and consumer electronics. Scientists of the University of Stuttgart, Germany, developed a 3-D-printed miniature spectrometer with a volume of 100 by 100 by 300 μm3 and a spectral resolution of up to 10 nm in the visible range. This spectrometer can be manufactured directly onto camera sensors, and a parallel arrangement allows for quick (“snapshot”) and low-profile, highly customizable hyperspectral cameras.


Femtosecond direct-laser writing as a 3-D printing technology has been one of the key building blocks for miniaturization in recent years. It has transformed the field of complex micro-optics since the early 2000s. Medical engineering and consumer electronics benefit from these developments. It is now possible to create robust, monolithic and nearly perfectly aligned freeform optical systems on almost arbitrary substrates such as image sensors or optical fibers.

Simultaneously, the miniaturization of spectroscopic measurement devices has been advanced with quantum dot and nanowire technology. These are based on computational approaches, which have the drawback of being calibration-sensitive and require complex reconstruction algorithms.

In a new paper published in Light: Advanced Manufacturing, a team of scientists, led by Professor Alois Herkommer from the Institute of Applied Optics and Professor Giessen from the 4th Physics Institute, University of Stuttgart, Germany, have demonstrated an angle-insensitive 3-D-printed miniature spectrometer with a direct separated spatial-spectral response. It has a volume of less than 100 by 100 by 300 μm3.

3D-printed spectrometer on a 100 x100 μm² footprint
a Measured normalised intensity profiles at the image plane of the spectrometer for illumination wavelengths ranging from 490 nm to 690 nm in 10 nm steps (monochromator, profile position is indicated in Fig. 3b). b Sinc² fits of the intensity profiles from a. c Centre positions of the sinc² fits per wavelength. d Wavelength shift per micrometre deduced from c. e Linewidth simulation and measurement with a red or green laser, respectively. The measured full width at half maximum is indicated with a pair of arrows. The combination of measurements d and e yield a spectral resolution of 9.2 ± 1.1 nm at 532 nm and 17.8 ± 1.7 nm at 633 nm wavelength. Credit: Andrea Toulouse, Johannes Drozella, Simon Thiele, Harald Giessen, and Alois Herkommer

The design is based on a classical grating spectrometer and was fabricated via two-photon direct laser writing combined with a super-fine inkjet process. Its tailored and chirped high-frequency grating enables strongly dispersive behavior. The miniature spectrometer features a wavelength range in the visible from 490 nm to 690 nm. It has a spectral resolution of 9.2 ± 1.1 nm at 532 nm and 17.8 nm ± 1.7 nm at a wavelength of 633 nm.

Leading author Andrea Toulouse says, “With its volume of less than 100 by 100 by 300 μm3 we explore a whole new size range for direct spectrometers. An order of magnitude this small could only be realized by computational approaches until now. In contrast, we translate the spectrum directly into a spatially encoded intensity signal which can be read out with a commercial monochromatic image sensor.”

3D-printed spectrometer on a 100 x100 μm² footprint
The inset (white box) shows a microscope image of the fabricated spectrometer (left) and its optical design principle (right). Credit: Andrea Toulouse, Johannes Drozella, Simon Thiele, Harald Giessen, and Alois Herkommer

“For 3-D-printed microoptics, the complexity of the optical design marks an innovation. Refractive, diffractive and spatially filtering elements have never been combined in such a small volume to create a complex and monolithic measurement system.”

“Our spectrometer could be fabricated directly on a miniature image sensor as the tip of a distal chip endoscope. This way, regions in the human body could be examined with extremely high bending radii that were not accessible before” the scientists forecast. “It could also be an interesting approach for hyperspectral imaging where the spectrometer would be used as a unit cell (macro pixel). The redistribution of spectral energy instead of high-loss Fabry-Perot-filtering could thus enable highly efficient hyperspectral imaging sensors. The ever-growing world population could benefit from such a camera if it was used for spectral mapping in precision farming, for instance.”


Researchers create low-cost, AI-powered device to measure optical spectra


More information:
Andrea Toulouse et al, 3D-printed miniature spectrometer for the visible range with a 100 × 100 μm2 footprint, Light: Advanced Manufacturing (2021). DOI: 10.37188/lam.2021.002

Citation:
Engineers 3-D-print a miniaturized spectrometer (2021, February 9)
retrieved 12 February 2021
from https://phys.org/news/2021-02-d-print-miniaturized-spectrometer.html

This document is subject to copyright. Apart from any fair dealing for the purpose of private study or research, no
part may be reproduced without the written permission. The content is provided for information purposes only.


Speak Your Mind

LEAVE A REPLY

Please enter your comment!
Please enter your name here

Get in Touch

350FansLike
100FollowersFollow
281FollowersFollow
150FollowersFollow

Recommend for You

Oh hi there 👋
It’s nice to meet you.

Subscribe and receive our weekly newsletter packed with awesome articles that really matters to you!

We don’t spam! Read our privacy policy for more info.

You might also like